Package: Tektronix_TDS_210_&_220_1_year_CAL_VER_9500.mcz
Become a MET/SUPPORT Gold Member to download this package!

Details about Procedure Files

Below is a list of procedure files (.pro files) in the package.

Subprocedures and procedures files that only contain subprocedures have been excluded.

The references of the subprocedure files have been included.

Tektronix TDS 210: (1 year) CAL VER / 9500-1hd: 1.00

Tektronix TDS 220: (1 year) CAL VER / 9500-1hd: 1.00

Date: 2001-08-06

Revision: 1

Automated Reference: Datron 9500

Automated Reference: Datron 9510

Procedure ID No: 001218M006

Models covered: 210, 220

Source: Tektronix TDS 200 Series

Service Manual

Digital Real-Time Oscilloscope

071-0492-02

Source Author: N/K

Compatibility: MET/CAL 6.10 or later

Subprocedures:

Sub Wait for Operation Complete (OPC) IEEE/: 1.00

Sub Tek TDS2xx: Main Trigger IEEE/: 1.00

Required Files:

Additional equipment Required:

One Dual Input Coupler & Two 50 Ohm BNC Cables

The Procedure was tested using:

Model No TEKTRONIX TDS 220

Serial No BO11062

Options N/A

Firmware Ver FV:v1.00

Module Firmware Ver TDS2CM:CMV:v1.04

The average run time during testing was 20 minutes.

Procedure history:

21-06-01: New Procedure

The procedure is intended for use with Met/Cal(r) calibration software,

and the terms and conditions set forth in your METCAL license apply to

this procedure.

Due to our policy of continuously up dating our products, this procedure

may contain minor differences in specification to those found in the manual

or other documentation. While every effort has been made to ensure that

this procedure is accurate, Fluke cannot be held responsible for the

consequences of error or omissions found within this procedure.

The copyright in this procedure is owned by Fluke Precision Measurement

Limited.

Tektronix TDS 210: (1 year) CAL VER / 9500-3hd: 1.00

Tektronix TDS 220: (1 year) CAL VER / 9500-3hd: 1.00

Date: 2001-08-06

Revision: 1

Automated Reference: Datron 9500

Automated Reference: Datron 9510

Procedure ID No: 001218M007

Models covered: 210, 220

Source: Tektronix TDS 200 Series

Service Manual

Digital Real-Time Oscilloscope

071-0492-02

Source Author: N/K

Compatibility: MET/CAL 6.10 or later

Subprocedures:

Sub Wait for Operation Complete (OPC) IEEE/: 1.00

Sub Tek TDS2xx: Main Trigger IEEE/: 1.00

Required Files:

Additional equipment Required:

One BNC (f/m) Right Angle Adaptors (Pomona 90191 Model 3534)

The Procedure was tested using:

Model No TEKTRONIX TDS 220

Serial No BO11062

Options N/A

Firmware Ver FV:v1.00

Module Firmware Ver TDS2CM:CMV:v1.04

The average run time during testing was 20 minutes.

Procedure history:

21-06-01: New Procedure

The procedure is intended for use with Met/Cal(r) calibration software,

and the terms and conditions set forth in your METCAL license apply to

this procedure.

Due to our policy of continuously up dating our products, this procedure

may contain minor differences in specification to those found in the manual

or other documentation. While every effort has been made to ensure that

this procedure is accurate, Fluke cannot be held responsible for the

consequences of error or omissions found within this procedure.

The copyright in this procedure is owned by Fluke Precision Measurement

Limited.