Package: tek_tds7000_1yr_ver_ieee_9500_6681.mcz
Become a MET/SUPPORT Gold Member to download this package!
Procedures in Package
Click on the procedure names to find out details about the procedure files containing them.
Tek CSA 7154: (1 year) VER IEEE /9500+3200+1Ch,6681, Revision: 1.4
Tek CSA 7154: (1 year) VER IEEE /9500+3200+5Ch,6681, Revision: 1.4
Tek TDS 7154: (1 year) VER IEEE /9500+3200+1Ch,6681, Revision: 1.4
Tek TDS 7154: (1 year) VER IEEE /9500+3200+5Ch,6681, Revision: 1.4
Tek TDS 7254: (1 year) VER IEEE /9500+3200+1Ch,6681, Revision: 1.4
Tek TDS 7254: (1 year) VER IEEE /9500+3200+5Ch,6681, Revision: 1.4
Details about Procedure Files
Below is a list of procedure files (.pro files) in the package.
Subprocedures and procedures files that only contain subprocedures have been excluded.
The references of the subprocedure files have been included.
Tek CSA 7154: (1 year) VER IEEE /9500+3200+1Ch,6681
Date: 2009-04-06 08:04:47
Revision: 1.4
Automated Reference: Datron 9500
Automated Reference: Datron 9530
Automated Reference: Philips PM 6681
Tek CSA 7154: (1 year) VER IEEE /9500+3200+5Ch,6681
Date: 2009-04-06 08:04:50
Revision: 1.4
Automated Reference: Datron 9500
Automated Reference: Datron 9510
Automated Reference: Datron 9530
Automated Reference: Philips PM 6681
Models covered: CSA 7154
Source: Tektronix CSA 7000 Series Performance Verification
Manual, Part No. 071-7011-00, August 30, 2002
Compatibility: MET/CAL 6.11A or later
Additional Equipment Required:
Coaxial cable, 20", 50 Ohm, SMA (m-m), 2 ea.
Terminator, short circuit, SMA, 2 ea.
Coaxial cable, 50 Ohm, BNC(m) to SMA(m)
Terminator, feedthrough, 50 Ohm, BNC
Coaxial cable, 50 Ohm, BNC, (m)-(m)
Attenuator, BNC, 2X
Tee, BNC, (f)-(m)-(f)
Adapter, BNC(m) to SMA(f)
Tee, SMA, (f)-(m)-(f)
The Procedure was tested using:
Model No. : 7254
Serial No. : Q0725012G
Options : 4M,SM ST
Firmware Rev.: 1.3.0
The average run time during testing was 70 minutes.
The copyright in this procedure is owned by Fluke Precision Measurement
Limited.
Tek TDS 7154: (1 year) VER IEEE /9500+3200+1Ch,6681
Date: 2009-04-06 08:04:53
Revision: 1.4
Automated Reference: Datron 9500
Automated Reference: Datron 9530
Automated Reference: Philips PM 6681
Models covered: TDS 7154
Source: Tektronix TDS 7000 Series Performance Verification
Manual, Part No. 071-0898-00, August 30, 2002
Compatibility: MET/CAL 6.11A or later
Subprocedures: Sub Tek 72XX DC VOLTAGE MEAS /9500+3200
Sub Tek 72XX BANDWIDTH MEAS /9500+3200
Sub Tek 72XX TRIG LEVEL /9500+3200
Sub Tek 72XX TRIG CHECK /9500+3200
Sub Tek 72XX DELTA TIME CHECK /9500+3200
Sub Tek 72XX CROSSTALK CHECK /9500+3200
Required Files: tds7000_Dtime_9530.bmp
Additional Equipment Required:
Terminator, 50 Ohm, BNC(m), 3 ea.
Coaxial cable, 20", 50 Ohm, SMA (m-m), 2 ea.
Terminator, short circuit, SMA, 2 ea.
Coaxial cable, 50 Ohm, BNC(m) to SMA(m)
Terminator, feedthrough, 50 Ohm, BNC
Coaxial cable, 50 Ohm, BNC, (m)-(m)
Attenuator, BNC, 2X
Tee, BNC, (f)-(m)-(f)
Adapter, BNC(m) to SMA(f)
Tee, SMA, (f)-(m)-(f)
The Procedure was tested using:
Model No 7254
Serial No Q0725012G
Options 4M,SM ST
Firmware Rev 1.3.0
The average run time during testing was 90 minutes.
The copyright in this procedure is owned by Fluke Precision Measurement
Limited.
Tek TDS 7154: (1 year) VER IEEE /9500+3200+5Ch,6681
Date: 2009-04-06 08:04:57
Revision: 1.4
Automated Reference: Datron 9500
Automated Reference: Datron 9510
Automated Reference: Datron 9530
Automated Reference: Philips PM 6681
Models covered: TDS 7154
Source: Tektronix TDS 7000 Series Performance Verification
Manual, Part No. 071-0898-00, August 30, 2002
Compatibility: MET/CAL 6.11A or later
Subprocedures: Sub Tek 72XX DC VOLTAGE MEAS /9500+3200
Sub Tek 72XX BANDWIDTH MEAS /9500+3200
Sub Tek 72XX TRIG LEVEL /9500+3200
Sub Tek 72XX TRIG CHECK /9500+3200
Sub Tek 72XX DELTA TIME CHECK /9500+3200
Sub Tek 72XX CROSSTALK CHECK /9500+3200
Required Files: tds7000_Dtime_9530.bmp
Additional Equipment Required:
Coaxial cable, 20", 50 Ohm, SMA (m-m), 2 ea.
Terminator, short circuit, SMA, 2 ea.
Coaxial cable, 50 Ohm, BNC(m) to SMA(m)
Terminator, feedthrough, 50 Ohm, BNC
Coaxial cable, 50 Ohm, BNC, (m)-(m)
Attenuator, BNC, 2X
Tee, BNC, (f)-(m)-(f)
Adapter, BNC(m) to SMA(f)
Tee, SMA, (f)-(m)-(f)
The Procedure was tested using:
Model No 7254
Serial No Q0725012G
Options 4M,SM ST
Firmware Rev 1.3.0
The average run time during testing was 70 minutes.
The copyright in this procedure is owned by Fluke Precision Measurement
Limited.
Tek TDS 7254: (1 year) VER IEEE /9500+3200+1Ch,6681
Date: 2009-04-06 08:05:00
Revision: 1.4
Automated Reference: Datron 9500
Automated Reference: Datron 9530
Automated Reference: Philips PM 6681
Models covered: TDS 7154
Source: Tektronix TDS 7000 Series Performance Verification
Manual, Part No. 071-0898-00, August 30, 2002
Compatibility: MET/CAL 6.11A or later
Subprocedures: Sub Tek 72XX DC VOLTAGE MEAS /9500+3200
Sub Tek 72XX BANDWIDTH MEAS /9500+3200
Sub Tek 72XX TRIG LEVEL /9500+3200
Sub Tek 72XX TRIG CHECK /9500+3200
Sub Tek 72XX DELTA TIME CHECK /9500+3200
Sub Tek 72XX CROSSTALK CHECK /9500+3200
Required Files: tds7000_Dtime_9530.bmp
Additional Equipment Required:
Terminator, 50 Ohm, BNC(m), 3 ea.
Coaxial cable, 20", 50 Ohm, SMA (m-m), 2 ea.
Terminator, short circuit, SMA, 2 ea.
Coaxial cable, 50 Ohm, BNC(m) to SMA(m)
Terminator, feedthrough, 50 Ohm, BNC
Coaxial cable, 50 Ohm, BNC, (m)-(m)
Attenuator, BNC, 2X
Tee, BNC, (f)-(m)-(f)
Adapter, BNC(m) to SMA(f)
Tee, SMA, (f)-(m)-(f)
The Procedure was tested using:
Model No 7254
Serial No Q0725012G
Options 4M,SM ST
Firmware Rev 1.3.0
The average run time during testing was 90 minutes.
The copyright in this procedure is owned by Fluke Precision Measurement
Limited.
Tek TDS 7254: (1 year) VER IEEE /9500+3200+5Ch,6681
Date: 2009-04-06 08:05:03
Revision: 1.4
Automated Reference: Datron 9500
Automated Reference: Datron 9510
Automated Reference: Datron 9530
Automated Reference: Philips PM 6681
Models covered: TDS 7154
Source: Tektronix TDS 7000 Series Performance Verification
Manual, Part No. 071-0898-00, August 30, 2002
Compatibility: MET/CAL 6.11A or later
Required Files: tds7000_Dtime_9530.bmp
Additional Equipment Required:
50 Ohm BNC terminators(m), 3 ea.
50 Ohm coaxial cable SMA (m-m), 2 ea.
SMA short circuit terminator, 2 ea.
SMA(m) to SMA(m) cable, 20", Tek 174-1427-00, 2 ea.
BNC(m) to SMA(m) cable
50 Ohm BNC feedthrough terminator
BNC(m) to BNC(m) cable
2X BNC Attenuator
BNC(m) to BNC(f) tee connector
BNC(m) to SMA(f) adaptor
SMA(m) to SMA(f) tee connector
The average run time during testing was 70 minutes.
The copyright in this procedure is owned by Fluke Precision Measurement
Limited.
Models covered: CSA 7154
Source: Tektronix CSA 7000 Series Performance Verification
Manual, Part No. 071-7011-00, August 30, 2002
Compatibility: MET/CAL 6.11A or later
Additional Equipment Required:
Terminator, 50 Ohm, BNC(m), 3 ea.
Coaxial cable, 20", 50 Ohm, SMA (m-m), 2 ea.
Terminator, short circuit, SMA, 2 ea.
Coaxial cable, 50 Ohm, BNC(m) to SMA(m)
Terminator, feedthrough, 50 Ohm, BNC
Coaxial cable, 50 Ohm, BNC, (m)-(m)
Attenuator, BNC, 2X
Tee, BNC, (f)-(m)-(f)
Adapter, BNC(m) to SMA(f)
Tee, SMA, (f)-(m)-(f)
The Procedure was tested using:
Model No. : 7254
Serial No. : Q0725012G
Options : 4M,SM ST
Firmware Rev.: 1.3.0
The average run time during testing was 90 minutes.
The copyright in this procedure is owned by Fluke Precision Measurement
Limited.